Well, Well, Well

We had exciting work going on at the farm this past Monday. A little before noon, several big trucks came up the drive. The well drillers had arrived! 

We didn't expect this project to be started for another month but there was evidently an issue with another job. The crew asked if we were ready now - you bet! We've been planning the irrigation well since Summer, doing field layouts and system design with an irrigation company, and searching for someone who would actually take the drill job. We needed 75 gallons per minute flow, which caused two local companies to decline attempting it. 

Reaching out a little farther, we used Gingrich from Kalona. These guys were great in every way. 

We were still a little concerned in the beginning, after a site survey. The result was: "If you were one mile North I'd no-quote it, but down here in the bottom, we've got some possibilities." Evidently there's a stone shelf coming out of the bluffs to the North of us and the ideal water location is under there. There would be no way to know if we'd get the water we need until the drill is in the ground. We were hoping for maybe 50% of our requested flow and plan-B was to adjust the irrigation layout accordingly.

I pulled in the driveway for lunch and found this welcome sight. The truck on the right is carrying the drill rig and the truck on the left is a dedicated tanker which carries all the water needed for boring lubricant and final flushing. I'd say the water truck was 1,500-2,000 gallons capacity or so.

The drill rig was pretty big. The building to the left is over 20' tall for reference. There is a trailer to the right in the picture which was carrying the casing tubing, grouting sand, and drill fluid mix. The first job is to drill a 3" pilot hole to find out if the water is at the expected location. If not, the well has to be abandoned and plugged.

Huge relief, the water was there! We were thrilled after expecting to see 50 gallons per minute output, the well actually test pumped at 90 gallons per minute!

Here's a shot of the primary casing drill bit. It makes a hole roughly 12" diameter. The spiked wheels on the end rotate and the truck's pumps force water down the center of the bit while drilling.

This is the suction screen which goes in the bottom of the hole. It is slotted stainless steel and keeps the larger sand particles from getting to the pump. The pump will go down inside this tube, which is about 8' long and it's 8" diameter. This well is cased at 8" and will use a 4" pump. I'm quite intrigued by the design of submersible well pumps. Due to limitations on the diameter of the casing, pump companies have to design quite large pumps which fit in a relatively narrow cylinder. Our pump and motor assembly will be almost 72" long but only 4" diameter!

Here's a short video of some flushing done to clear any debris from inside the well casing. The whole system will be sanitized when the pump is installed and eventually tested by a sanitarian who is certified to test for the USDA, as required for organic certification. Marion county can't test for the USDA requirement but Mahaska county has someone who can, so that shouldn't be an issue down the road.

Dirt Bags

Our shipment of dirt and compost has arrived! There are 15x super-sacks holding two cubic-yards each. It was a 35,000 lb load. This should be enough to get us through 2020.

A large amount (12x bags) is compost for field amendments. This will be spread on the raised beds as we build and plant them. The remaining three bags are seed starting mix and soil for "potting-up" the starts to larger pots.

All of these items are OMRI listed and certified organic. This is required for our supply-chain management to ensure our own organic certification eligibility in the future.

I'm not real pleased with the amount of plastic film required to ship these. We might explore bulk shipping (like a dump-truck), if available, in the future. I imagine it's difficult to bulk ship certified-organic items when there might be non-organic items remaining in the truck box from the previous shipment or some other contamination.

We're excited! It's snowing today but we still think of field work!

New Arrivals

The baby chicks are starting to come in! We have 30 new ones today and another 25 due in next week. There has been a big demand for eggs so we've added as many birds as we can to our coop arrangements. We may have to plan for a building expansion next year.

This new flock will be similar to the current producers which is a wide variety, producing all sorts of egg colors.

Greenhouse Improvements

I've been doing a few updates to the greenhouse. The house manufacturer sells wind/snow structural kits to make the frame stronger. These tie the vertical wall poles to the ground, keeping the poles from pulling out, while also preventing the "A" shape of the roof from spreading out. The previous owner of this greenhouse never had these but they were setup right next to another building. Our location is out in a field so I decided to add the extra reinforcements. 

The main anchor component is a 36" earth-auger that has to be installed at each reinforcement. For my driver, I used an extra 35mm wheel-bearing socket (for a long-gone vehicle I owned years go) with a couple tabs welded to it. The auger eye almost fits into the socket, and the ears go along the sides of the eye to turn it. This worked pretty well and a 1/2" impact gun installed each auger in about 45 seconds.

Then it's just drilling a hole in the pole and assembling the turnbuckle hardware.

Since the value of the greenhouse contents can be quite significant (nearly the whole spring planting, for example), we added some electronic monitoring. This device monitors the temperature and humidity in the greenhouse. It also monitors if the power is on and has a built in battery for sending alarms when the power goes out. 

It will call/text/email if parameters fall outside of the alarm ranges. The primary concerns are too cold in the winter/spring, and too hot (or too humid) in the summer.

The data-logging from the monitoring device really shows how well the greenhouse can capture the sun's energy. Yesterday, the high temperature outdoors was 28°F but the greenhouse got over 96°F in the afternoon because the sun was out for a little while. On a cloudy day it's not quite that good but it still runs at least 20°F higher than ambient.

Winter Weather Advisory

January provided some energetic winter weather this year. It's not uncommon for us to have ice storms in Iowa but the duration of this one was pretty impressive. Some flat surfaces appeared to have almost a half-inch!

Not too long after the ice, we got a couple rounds of really wet snow. It reminded me of a mountain landscape, with the coniferous trees bent down to the ground.

The greenhouse has been handling the snow very well. It's a A-frame or "gothic" frame shape so it has enough pitch that most precipitation slides off. 

The snow which slides off makes pretty big piles on the sides. As a preventative measure, I run along the sides with a snow-blower to make room. As you can see here, the snow was already deep enough to get up to the rounded part of the roof. I figure if I didn't get rid of it, the next snow would have nowhere to go.

Poultry prophecy in the cirrus clouds.

I looked out behind the chicken-coop a few evenings ago and noticed a large cloud formation which looked like a bird (over on the left) with a long tail (and maybe the bird's wing is on fire?). We've got 30 more hens on order so it seemed an appropriate display.

Almost planting time!

Soon the green-house will be running and we'll have our first plants germinating. Our supplies have nearly all arrived, including our three-row planter!

I'm excited to see how this works in the field. The front wheels provide drive to a chain on the side which is turning a shaft, running through all the planter sections. There is a little knife and a cover plow for each row. Apparently it's possible to hack/fit five rows on this unit if one purchases some spare parts to modify it. Out of a couple different varieties of micro planter available, this one is known to be least finicky about soil bed preparation.

The seed hoppers contain a wheel which is changed out for each different seed size/shape to be planted. There is a small brush and guide plate which are consumables. You can see the drive sprocket to the side of the wheel. The drive-ratio at the wheel chain can be changed to modify the seed spacing along the row. We will be using this planter for radishes and carrots initially. It can also be used for beans, peas, sunflowers and corn.

Here's one of our seed shipments. Corrine has been organizing these into folders by week. Each folder contains everything needed for that week, and instructions on what to do next. We're trying to apply lots of energy to "pre-work" and planning to that, during the high-labor part of the season, all we have to do is run to the plan.